![]() ![]() This results in the following power requirement in Ah (ampere hours) without “Power Save Mode”: 0.65 A (HELIX DSP ULTRA) + 2 x 2 A (amplifiers) x 0.25 hours = 1.16 Ah. The HELIX DSP ULTRA therefore also remains switched on for the same period of time as well as the two power amplifiers connected! After you have left the vehicle, the factory radio remains “invisibly” switched on for 15 minutes. The remote output of the HELIX DSP ULTRA drives two 4-channel amplifiers, each with a typical quiescent current of roughly 2 amps (quiescent current = amplifier switched on, but no music signal present). Here‘s a sample calculation for a better understanding:Ī HELIX DSP ULTRA is connected to the speaker outputs of a factory radio and is switched on and off by this. This means that any audio device that is connected to the loudspeaker outputs of the OE radio will also remain active and draw a lot of current from the battery. Nowadays, many vehicles are equipped with “CAN” or similar bus systems that leave the radio “invisible” turned on for up to 15 minutes, even if you have meanwhile switched off the ignition and left the vehicle. The “Power Save Mode” can significantly reduce the power consumption of your device and the amplifiers connected to it if there is no input signal for a longer time. ![]() Tick this checkbox if you do not want to use the "Mode Switch". IMPORTANT: In both setups, the mode switch must be configured as “Setup Switch”.įor devices with ACO, you can select in the DCM menu in the tab “ACO Features” between which two setups shall be switched. When using a product without ACO, the two existing setups 1 & 2 are switched: The functionality depends on whether you have an ACO device or not. In order to be able to use this function correctly, it is necessary to adapt the configuration in Signal Management:Īllows you to toggle between two setups. In order to be able to use this function correctly, it is necessary to adapt the configuration in Signal Management:Īctivates the AUX input or the input of the extension card module (HEC / MEC / BEC) of the device when the push button is pressed. One of the following functions can be realized with the push button on the remote control:Īctivates the digital input of the device when the push button is pressed. ![]() Tick this checkbox if you do not want to use neither "Control 1" nor "Control 2" on your remote control. The virtual channels “Rear L Full” and “Rear R Full” are affected. This function is only available for devices with active VCP. In this mode, the virtual channels “Subwoofer1” and “Subwoofer2” are always controlled by the subwoofer volume if you activate them.Ĭontrols the volume of the rear channels. In order to have a maximum flexible configuration, it is necessary to activate VCP.Īs soon as VCP is active, you can use the routing of the virtual subwoofer channels to determine which output channels receive a controlled signal. If you haven’t activated VCP in the DCM menu, you can recognize the controlled channels by the fact that they are defined as “subwoofer” in the standard setting. With VCP-capable devices you can always recognize the controlled channels by the marking in the channel name: With the latter, the subwoofer volume control is activated by assigning the corresponding output channel in the IO menu as a subwoofer via its name: The configuration of output channels as a subwoofer differs between devices that are VCP-capable (crosslink) and devices that do not support VCP. like DVD players) do not have their own volume controls.Īdjusts the volume of the subwoofer channels. ![]() The other input signals remain unaffected.Īdjusts the volume of a digital signal source that is connected via the optical or coaxial SPDIF input. It is therefore not necessary to change the volume on the signal source itself. This is useful if your signal source does not have its own volume control.Īdjusts the volume of an AUX source or an extension card module (HEC / MEC / BEC). Depending on the product and its feature set, the selection may be limited.Īdjusts the volume of all output channels simultaneously. Of course, it is not possible to assign the same function to both controllers. The rotary controls "Control 1" and "Control 2" can be assigned any of the following functions. This wired remote control has two rotary controls and a push button, the function of which you can determine yourself. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |